Видео

great job

It's such a great looking car. Aging really well. I currently own an E60 530i M Sport 6-speed manual N52 engine. Still considering selling both my E60 and Porsche 911 and buy an E60 M5

Was this car on original Rod Bearings 140k?

Great video, thanks a lot <3

How on earth ar we supposed to remove and install the radiator plugs? They are a nightmare and i broke all 4 of mine

This is the proceedment for the m3 e46 USA version... When I saw my car and then your video I thought what car I have bought ?? XD EU version has diferent monitoring lambda sensors location because the CATs location is different. They are under the car at the middle... I used ISTA + for the documentation but thank you for the video. 🤝

Why do you have to take em off before a smog?

No sir...I couldn't even sometimes drive manual, let alone daily it

What intake heat shield is that?

Hi. Where is the link for that sway bar?

Brother really said I spent about 12,000 after having said 6500 and 8000 at separate points

The biggest question does it bounce lol

Need the part# for the oil cooler keep finding nothing but the transmission oil cooler

Thank you for the video. Question, my rotors are in good condition and don't need resurfacing, but need to put new pads, can i do the bedding just like you did or do i have to remove the old pad bedding from my old rotors?

cool

@Teo Corrales , do you still own a car after 4 years?

❤❤❤❤❤

☺️ *Promosm*

This vid is 3 years old now. Tell me, how do you like your Magnaflow after all this time? Is it much louder than stock in normal driving? More responsive? I'm looking at buying a Cat-back and your advice would be helpful. Thanks in advance.

tfti to the toyota day things

Hey neat i was there

green coolant? any chance that's why the radiator was smoked in just 4 years?

Can the air be bleed out of the system by letting the engine run for 5-10 minutes?

How was visiting Fuji Speedway? Did you go for any specific day or event?

Great Video, Thanks Teo. Keep it up !

😂😂 nah the very beginning has me in bits.

Good video!

Is bedding only for new rotors or do you need to bed new pads on old rotors?

ISSUES ON E60 M5 IS OVER HYPED. I HAD 2 OVER 200K ON STOCK ROD BEARINGS.

I could use your services on my E46 M3

Where are you located

Very good and clear advise: Thank you very much!

This looks nothing like my oil cooler and I have a 2004 e46 (325 ci) my oil cooler is small and is on driver side and pushes into radiator. It’s maybe 1/3 of the size your holding so what car is that?

Great video but you provided a wrong part number link in your description. That is an OEM length end link! Can you please let us know what is the part # for the short ones you installed?

Damn bro I’m having a difficult time removing the Bank 2 pre Cat O2 sensor

Mine only came with one long plug and one short plug. I thought I just had to switch the short one to the driver side and the long one to the passenger side. But apparently not 😬

Couldn't you use some spring compressors to make front strut removal easier?

Can I use a auto radiator and just use the shirt plug ?

Great video dont stop

Did you bleed the air our of the oil cooler?

It has two idle actuator, and two throttle actuator. They are different parts. When the idle actuator goes bad you will have DSC/CHECK ENGINE/DBC/Hill start/ lights on because the engine cannot generate enough vacuum force.

What’s the right part of the thumbnail

So i contacted the scan tool company you posted and they told me it’s not compatible with 06 m5’s, my question is are there functions that don’t work with your car or does everything in the tool work correctly. I want to purchase but they don’t have a refund policy

Who did the manual swap?

Great video

Do you hold the break down or tap it

Good to know,. Have been wondering about that. Thank you man.

How long did the 6spd trans swap took you?

You might need these $1000 coils if you are boosted to over 600 RWHP. Otherwise, a set of Six ELDOR coils for $145 will be PLENTY good up to 600 RWHP. Most of BMW now uses ELDOR coils. Bosch, then Delphi, and finally ELDOR. Eldor Part number cross reference R3516S00100 for E46 M3 The ULTIMATE BMW Ignition Coil Guide | 2003 & Newer ruclips.net/video/Tjsx-K1mjkQ/видео.html

Dielectric grease is not necessarily recommended by BMW, but many people put a VERY thin coat on the inside of the first two inches of each coil boot. Must be a THIN coat. No never seize should be used with NKG Platinum plugs. Their threads are plated specially.